In this post, we are going to discuss some of the main problems of solar panels because the houses in which solar systems are installed to generate electricity have to face some of these problems.
Today we will talk about these problems. We will discuss many things like dirty panels, inverter problems, shadows, wiring problems, weather damage, poor fitting, etc.
1.Dirty solar panels
Often, due to dust, dirt or environmental pollution, some such particles of dirt get stuck on the solar panels, apart from this, birds also come and sit on them in some places, due to which the sunlight does not fall directly on the solar cell and due to which the electricity generated is reduced.
Solution
Solar panels should be cleaned from time to time with a soft brush and a little shampoo, because if you use a hard brush, the glass of the solar panel will get scratched, due to which the warranty of the panel will expire and its performance will also decrease.
If you do this from time to time, you will have very less problems of low electricity generation from panels.
2.Frequent breakdown of the inverter
The inverter plays a major role in converting DC power from solar panels to AC power, it can often get damaged or even burn.
For this, try to install the inverter in a place where there is more air circulation and it is also protected from water.
Never place the inverter in direct sunlight. It is often seen that if we place the inverter in high heat, then after overheating, the internal components get damaged.
Secondly, keep checking the DC power supply coming from the solar panels from time to time. Sometimes, due to loose connections, the inverter can also get damaged due to sparks.
Devices also come for the protection of the inverter, ACDB, DCDB, they must also be installed.
Along with this, the one that is grounded should also be checked from time to time because the life line of the inverter depends on the ground. ACDB DCDV will also work only if your ground is correct.
Get the grounding done properly and keep checking it from time to time
3.Shadow
Often there are places where there are trees around or sometimes there are buildings or sometimes there are other structures which cast a shadow on the solar panels.
Also, the electricity production will be very low, try to install the solar panels in advance and protect them from the shade. If any such problem arises, try to solve it
4.Wiring and Connections
As we have already discussed above, loose connections, bad wires or poor quality wires can disrupt the flow of electricity, because wherever the wire connection is loose or the connection is loose, the connection gradually gets hot and burns.
With which many problems can arise, so keep checking the connectors etc. from time to time.
5.Impact of weather like wind, hail, etc.
Weather can cause a lot of damage, such as the most damaging wind, hail, or in some places, heavy snowfall or serious weather problems can also cause damage to them.
If there are strong winds and winds in your area, then first of all, the structure of your solar panel on which the solar panels are fastened should be strengthened.
Because when you install a new solar panel, at that time, there will be a difference of maximum five thousand rupees. If there is damage after fitting, then that damage would be bigger.
Therefore, try to strengthen it in advance.
6.Poor fitting installation
Poor installation. Sometimes the installers of solar panels are unknown people or they do it in a hurry, or they use bad materials, and if your installation is bad, then you have to face very big problems.
7. Temperature
This is also a big problem, if there is too much heat on the solar panels, then your electricity production can be very low. It has been observed that the right temperature is between zero degrees and 48 degrees.
If the temperature is more than 50 degrees, then the solar panel will not give you much benefit at that place.
8.Solar panel technology
Whenever you want to install a solar system in your house, first try to get information about the new technology, such as first poly crystal line, then mono crystal line, then monopark, then mono half cut, then bifacial, then the latest technology that is used today, Topcon.
That is, whenever you install solar, first find out which technology has come new in the market because there is no difference in their price. |
9. roof
If we talk about the roof, it is best if your roof is made of concrete material because when rain and wind come, then the roof with tin roof can be damaged, or the structure that comes with it should be installed in such a way that it is not affected by any rain and wind. |
ac चलाने से बिजली का बिल कैसे कम करें यह पोस्ट पढ़े
10. Solar panel technology
Selection of good quality solar panels As we have discussed above, along with new technology, solar panels of good companies should also be installed because it is often seen that the cheap panels come with micro cracks, meaning that the cells that come break.
When these cells break, you will not get the full energy that they provide, so never install low-quality panels.
Some people also sell old solar panels in the market. if you find them at a very low price, you can buy them; otherwise, try to install new solar panels. If today the price of a solar panel of 540 watts is around 8000 to 10 thousand rupees, then this is valid if you get the old solar panels of 330 watts for 2000 rupees. if you get a panel of 5000 rupees, then you should install a new panel instead.
Because it takes up more space, the efficiency it provides is also quite low, and the 350-watt panel will only give you 200 watts of power at most.
I have tried to provide some information that may be useful to you. Thank you for reading the post.
